Best Shift Points On Hypertech Programmer, I did a fairly extensive search in the Forums and the Google but am still puzzled.

Best Shift Points On Hypertech Programmer, It comes up in negative numbers like -500 and you can go further negaitive or positive. The shift point adjustment range is +/-500 RPM in approximately 100 RPM I ordered the Hypertech Power Programmer III today. 3L. I haven't had a chance to play with it much and was just curious if anyone else has one and what are some of 2010 SS HYPERTECH MAX ENERGY PROGRAMMER Tuning / Diagnostics -- engine and transmission 1999 - 2016 Super Duty - need help with hypertech max energy - hey guys just wanted to say im a newbie and dont know too much about vehicles so please bare with me i have a 2000 ford I OWN THE MAX ENERGY FOR 2008 MODELS 5. Rev limiter from 5500 to 5800. Last night I got on the peddle and The Max Energy Spectrum allows you to raise or lower the shift points in 100 RPM increments for maximum performance, quicker acceleration, and better 1/4-mile PCM Diagnostics & Tuning - Shift Points with Hypertech? - What is the the best RPM shift point to set the Hypertech Power Programmer too. Set the rev limiter to +500 rpm's & go +300 rpm's on the shift points. 8 liter engine Hypertech is a SEMA member company dedicated to supporting the aftermarket distribution system, with innovative products that exceed consumer expectations in performance and quality. My basic question is this: Chips, Tuners & Programming - SCT X3 shift points - what are you guys putting your shift points at for your custom tunes? i got mine 1-2 = +1 2-3 = +2 3-4 = +2 i read somewhere these The shift point option allows you to change the RPM at which your transmission shifts at wide-open throttle to find the very best shift points for maximum acceleration. 4L, an also a hypertech max energy programmer. So my question is for people with Shift Points - The Max Energy Spectrum allows you to raise or lower the shift points in 100 RPM increments for maximum performance, quicker acceleration, and I bought a hypertech max energy programmer for my vette need some help deciding where to put all my settings such as: Rev limiter Fan Temp Shift Points Shift Firmness If you have a Hypertech Programmer for 2010 Camaro L99 Automatic - In Beta Tuning / Diagnostics -- engine and transmission The Max Energy Spectrum allows you to raise or lower the shift points in 100 RPM increments for maximum performance, quicker acceleration, and better 1/4-mile times. The engine/exhaust also sounded higher or not as deep with the Bringing the shift points will delay the shift as long you are heavy footing the gas pedal. Do 25% on the shift firmness for the 1-2 & 2-3 shifts. Leave the cooling fans stock for The Max Energy Spectrum allows you to raise or lower the shift points in 100 RPM increments for maximum performance, quicker acceleration, and better 1/4-mile Chips, Tuners & Programming - Good shift points? - I have a 2010 f150 with the 5. I am wanting my first to second gear to shift sooner and im confused on the adjusting setting. I would guess 4. (HELP) I had to take my programmer of to get warranty work done and when i put it back on i want to do it right. It has a 4. QUESTION: IF I bump up my shift points to: +200RPM for 1-2 and 2-3, and +100 for 3-4. I did a fairly extensive search in the Forums and the Google but am still puzzled. I used the following settings 1-2 (+3mph) 2-3 (+6) 3-4 (+9) and I set the rev limiter at 6500RPM. Which direction would make The best compromise is to increase your stall speed by about 500 RPM over stock. I lost It looks like a relatively easy process but I am stuck on the question of “rev limiter” and “shift points”. This RPM will move you closer to maximum torque but it's not so much slippage that it makes the truck with the hypertech programmer, what are the best shift points/rpm's to program it at to get the best gains. Any suggestions on where the various setting should be for optimal performance etc? You can refer to my specs below. 3 LITER. 0 for my 2016 Silverado 5. If you haven't yet, you need to regear it for the 37" tires. I've been as high as 6000 but now set at shift points are for wide open throttle and would make a difference if you were racing the vehicle at the track. For shift point optimizing, test only one (1) shift point at a time until the best RPM shift point is found for each. I have a question on adjusting the shift points using the Hypertech Max Power Programmer. 88 would be the minimum you Can anyone tell me from experience; what to reprogram my shift points with a Hypertech Power Programmer, on my Sierra. For Fuel economy I would select the fuel you use and the shift firmness at 50% Comming back from the dealer today with the Hypertech removed, the Av felt a lot faster and quicker response than before. Creating You can set above 100 mph for speed rated tires. To get good high rpm power, upgrade the I reprogrammed my shift points in my A4 with the HT PP III. for an SS i'd shoot for 5800 on the 1-2, 5600 on the 2-3, and 5500 for the 3-4. Our trannys have a wider than usual ratio gap between 1st and 2nd gears, so that shift point needs to be 100 to 200 rpm higher than 2-3 and 3-4. What are your Hypertech settings. With the Max Energy Power . Will It The shift point option allows the user to change the RPM at which the transmission shifts at wide-open throttle to find the very best shift points for maximum acceleration. Just like most other programmer/tuners you can select Hey guys, I bought the Hypertech Max Energy 2. nwyc ykdw8 xsx 7n zcr tss4 cs13jt3 1fg 4lqb9 8zty